Monday, 10 August 2009

Door won't open!!


Just had to let you guys know about this one.

A workshop had spent hours trying to open the door on a Peugeot 1007.

Convinced they had a door lock fault they had almost destroyed the trim on the door trying to remove it, while the door remained firmly locked.

A global scan, that is a scan of all the electronic control units fitted to the vehicle revealed a fault code relating to the fuel filler cap. A new filler cap sensor and loom was fitted and hey presto the door opened.

But why, these vehicles are fitted with a sliding door that is prevented from opening when the filler cap is opened. This is a safety issue as the door would hit the fuel nozzle if it could be opened during re fuelling. With the sensor faulty the safe mode is locked.

Saturday, 18 July 2009

P0420 AGAIN!

This fault code seems to be cropping up more and more, by that I mean it comes back after the fix. But why?
Firstly lets understand the fault code and how its generated.
Modern cars have 2 O2 sensors, the first before the cat, monitors the oxygen content of the exhaust gas. It uses this to adapt the fuelling via the fuel trim to keep the mixture within acceptable limits. The 2nd sensor after the cat monitors the efficiency of the cat. If the switching ratio of the O2 sensor is similar then the cat isn't working. This ratio is monitored and once a set ratio is exceeded the fault code P0420 is set.
So why does this fault code come back?
There are 2 causes poor quality replacement parts, and not fixing underlying causes.
If you are presented with this code ensure before fitting a new cat the reason for the failure is correctly identified and fixed. Missfires will make short work of a new cat.
Once the cause is rectified ensure the replacement is of OEM quality, too often the returning code is down to the quality of the replacement parts.

Friday, 17 July 2009

Rally car trouble

This week we have a rally car to deal with. Once warm it cuts out, will not re-start until cold again. A simple temperature related problem so why has it proved so difficult to fix?
time to investigate.

Turns out a relay is failing.

Tuesday, 14 April 2009

No Codes No Fix

A local garage a had a few problems with this one.
The car cut out, and will not restart.
If left for 5 mins or 5 hours it will restart but cuts out then won't start again.

They tried to scan it for codes, but this resulted in the dreaded no codes found.
The vehicle did not support EOBD so no pending codes or freeze frame data.
This is where you need to have a basic understanding of the control systems.A few quick checks, and hey presto the Crank Angle Sensor is found to be faulty.
Once again checking inputs and outputs with a scope provides the answers when scan tools fail.
A new sensor restored normal operation.

Saturday, 4 April 2009

No fault codes what next?



Technicians are becoming more and more dependant upon fault codes. This is due to the increasing complexity of modern vehicles.


But how do you tackle diagnostic problems without codes.


The first example this week was a non starting Clio 1.4 single point injection.


No communication with the scan tool thus no codes.


Where do you start with this kind of problem?


One of my first tests is power to the injectors, this is a good idication of ECU, main engine relay, & earth are all ok.
In this case we had no power at the injector. The reason is proberly the cause of the non start.
Using the Autodata wiring diagram shown it is possible to work out where the feed comes from. The fuel pump relay, this checked out OK, so the main engine relay was tested, I tend to bridge them as a quick test and after this not only did the engine start but communication with the scanner was restored. Problem solved or was it, I haven't proved how it had failed. It turns out the switched earth signal from the ECU has gone missing, the wiring had gone Open Circuit.
A quick repair restored normal operation, but why had a new ignition coil been fitted in an attempt to get this vehicle going?
The garage had tested for a spark during cranking, not being able to gather codes resulted in a guess. The guess was based on previous experience of this system where coils had been known to fail.
Following a TESTING procedure that I have refined over years of diagnostic testing prevents costly mistakes.


Thursday, 31 July 2008

Nissan Touring car Missfire


Interesting one this, missfire complaint on a Nissan Primera.

No big shakes apart from the fact it is a 2000 super tourer.

A 2.5 l 320 BHP N/A engine.



But engines are engines and they all need fuel, spark and compression.

The visual inspection found a bad connector, on one of the eight yes eight injectors.

Once repaired and shaken down on the track all was good.

It is now racing and winning in the Welsh Saloon Car Championship.

For more details check out WRDA.co.uk

Friday, 4 April 2008

ABS trouble


Most ABS faults relate to the wheel speed sensors, the wiring or the physical condition of the system.
This Ford Puma was no exception, the pedal pulsed when driving, the ABS warning light was illuminated, and it was clear the vehicle had sustained some damage recently.
A quick look at live data showed one wheel speed sensor dropping out occasionaly, but why?
No need for scopes here the front left wheel speed sensor wiring had been damaged but not repaired when the panels had been replaced after a minor RTA. New sensors are expensive so a repair to the wiring loom was the option taken by the customer.